Pandaboard Support
Rob Heaton (274) 515 posts |
I’m debating getting a Pandaboard ES, especially after reading the recent benchmark results! I just have two questions; |
Wouter Rademaker (458) 197 posts |
1. Yes, this is send from a Pandaboard ES |
Rob Heaton (274) 515 posts |
Thank you! |
Keith Dunlop (214) 162 posts |
If you’re coming to Wakefield Rob you’ll see one in action as I am bringing mine. in response to your questions: 1) Like Wouter this is being sent from a PandaBoard However do not expect the same level of stability that you get with a BeagleBoard yet! |
Jeffrey Lee (213) 6048 posts |
In terms of volume, or quality, or what? After Willi spotted that the sound setup configure plugin wasn’t allowing you to use the full volume range available on the BB/PB I made some changes to the OMAP3 HAL and sound setup plugin to allow the extra volume range to be used. This has made a big difference to the volume output, with the maximum volume now being louder than an Iyonix. However I have noticed that there is some clipping/distortion if you set the volume too high. Note that you’ll need a recent hard disc image (Jan 22 or newer), otherwise the sound setup plugin will probably crash when you try to open it. |
Rob Heaton (274) 515 posts |
Curses! I’m destined to miss the Wakefield show every year :(
How unstable is RISC OS on the Pandaboard? |
Chris Gransden (337) 1208 posts |
It’s no less stable then RISC OS is normally. So not very! :-) It does seem a bit easier for misbehaving programs to bring the system down. Having to run a lot of programs with alignment exceptions turned off and there being no full protection for page zero probably doesn’t help. |
Colin Ferris (399) 1819 posts |
I use a little program called Protector by Andreas Feldner. |
Matteo (1478) 105 posts |
I have found some bugs in my pandaboard rev A3: at 1920×180 or 1920×1200 or a resolution higher than 1280×1024 there are some green lines over the images i dont know why this is caused, can be a bad video driver. Another bug is that opening progams like netsurf or copying files to hard disk make some sound noise like “poc poc”. |
Matthias Faust (490) 38 posts |
Another question: Does RISC OS support a monitor with DVI Input on the Panda ES via a HDMI to DVI cable? |
Matthias Faust (490) 38 posts |
@Matteo |
Keith Dunlop (214) 162 posts |
The lines you seeing are a known problem – you can see an example here (warning big jpeg!): http://www.usablerange.co.uk/RISCOS/screen5.jpg As I understand it this is being looked at. |
Keith Dunlop (214) 162 posts |
RISC OS supports the DVI output on the PandaBoard ES not the HDMI output so it is similar to the BeagleBoard. |
Matteo (1478) 105 posts |
The sound noise come directly from the speakers. I hope the issue with green lines will be adjusted soon: : ) |
Rob Heaton (274) 515 posts |
My Pandaboard ES arrived today! I think I’ll invest in a heat sink or two before running it at 1.5Ghz. (Just to be safe!) |
Chris Bass (1890) 2 posts |
I’ve ordered a panda board today & was wondering if there’s somewhere to look on how to get started, such as installing RISCOS? |
Wouter Rademaker (458) 197 posts |
You can read: |
Chris Hall (132) 3567 posts |
Unlike the Raspberry Pi, there isn’t a recommended SD card image available to download, not even from here (which does seem now to be a little dated). However R-Comp do a ‘PandaLand’ scheme which can provide a pre-prepared SD card with some very useful software, all included, at a price that is reasonable (£69.99). PandaLand provides PandaBoard owners with software and operating The other option is to download the Raspberry Pi SD card image (which offers a dual-partition card) and copy the relevant files into the FAT partition that are required to start up a Pandaboard. You will then need (under RISC OS) to replace the HardDisc4 files and directories with a plain vanilla HardDisc4 downloaded from the ROOL site. Use a fast SD card – 95Mb/s – as you will get about 21Mbyte/s read and write from it. |
Keith Dunlop (214) 162 posts |
Another request to get the SD-Card DIY how-to written then… Quite simply if you don’t want to DIY then there are commercial solutions out there where you can buy a pre-built SD-Card and off you go. Of course the advantage of DIY is that you are likely to be using a more recent ROM and you can start to really push the envelope of the hardware. One thing to note is that the OMAP4 ROM available from here is quite out of date for a number of reasons. |
Chris Hall (132) 3567 posts |
One thing to note is that the OMAP4 ROM available from here is quite out of date for a number of reasons. I presume you mean from the PandaLand scheme. Yes, it’s from a year ago. It did get some testing and is supported by RComp. But we’re all waiting for RISC OS 5.20 which is likely to be the next properly supported version. Of course it is easy to download and try the latest ROM but keep the older one in case you want to revert to it if something gets broken in the daily build. It is difficult to work out when a significant improvement makes it into the daily ROM build as there is so much detail to wade through. The ‘fix’ I am keen to see for the Pandaboard is the CTRL-SHIFT-f12 shutdown/restart hang. |
Keith Dunlop (214) 162 posts |
No, as I said, the version downloadable from ROOL is missing some of the latest features. Also I have just read that wiki page – yikes! how out of date is that!!!? See how you get on and feel free to ask when you run into problems in the Community Support part of these forums. |
Chris Hall (132) 3567 posts |
No, as I said, the version downloadable from ROOL is missing some of the latest features. Now that threw me – I hadn’t understood that ‘some of the leatest features’ hadn’t made it into the CVS repository. I was just following the ‘latest additions’ list waiting for something that was important to appear when I would download a daily build. Can you be more specific about what has been ‘fixed’ but has not yet made it into the CVS please? |
Chris Hall (132) 3567 posts |
No, as I said, the version downloadable from ROOL is missing some of the latest features. Now updated to version 5.2x [both ROM and HardDisc4] – the OMAP4 ROM downloadable from ROOL now therefore must have all these latest (but unspecified!) features. Unless, of course, they are still untested and unsubmitted hacks? |
Raik (463) 2062 posts |
Thanks for this info. But where is the stable release 5.20? Sorry, the wrong place. |
Chris Hall (132) 3567 posts |
I presume that the stable 5.20 version is currently a release candidate undergoing testing. There is at least one problem with it (sound plays too fast) and so it will be being tweaked and will only be released when it is working correctly. Development builds will be 5.21 even though 5.20 is not yet available. |