Extended Framebuffer Format Specification (Rev #4, changes)

Showing changes from revision #3 to #4: Added | Removed | Changed

This document is a proposal on how to extend the VDU system and sprite formats to handle the most common framebuffer formats and uncompressed bitmap layouts in use today. It is hoped that this can be achieved in full compatibility with developments to the RISCOS Ltd fork of the OS. Settings are defined as orthogonally as possible, in order to simplify their implementation.

Where applicable, colour components are consistently described in a big-endian format – for example modes with a colour number format of &TTBBGGRR is described as “TBGR”.

Mode variables

These should be all the necessary combinations of mode variables:

(*) – These aren’t really 2^6^ = 64 bpp. They can’t be addressed by a simple bitshift operation.

(**) – These aren’t really 2^7^ = 128 bpp. They can can’t be addressed on a pixel-by-pixel basis at all.

ModeFlags bits 12-15 are really now made up as follows:

When NColour 420 or 422 are in use, proposed ModeFlags bit 9 is used to describe the process used to perform horizontal chroma subsampling. Often, video plane hardware will only support one or the other of these.

Vertical chroma subsampling only applies to NColour=420. It is assumed to be always be such that the 0th chroma row is located between 0th and 1st luma rows. There are a cases where other possibilities arise, but these are probably rare enough not to worry about. Note that when converting to/from a 4:2:0 format, you also need to take into account the setting of ModeFlags bit 8 (the interlace bit).

The word at offset +12 of a mode selector block probably ought to be extended as follows:

All the other modes can be selected by overriding ModeFlags and NColours at the end of the mode selector block.

Sprite formats

In sprites, all this extra flexibility has to be squeezed into the 32-bit sprite mode word. RISCOS Ltd have reassigned bit 31 of the sprite mode word to indicate the use of an 8-bit “greyscale alpha” mask rather than the traditional 1-bit “binary alpha” mask. This means that the sprite type field, for which we now have many more settings, has been squeezed down to 4 bits and is far too small for our requirements. We require an alternate definition of the sprite mode word, and for backwards compatibility, it needs to be distinguishable from the defined alternatives. This is proposed to work like this:

000000000000000000000000smmmmmmm -> mode number
pppppppppppppppppppppppppppppp00 -> pointer to mode selector
w1111ttttttt0000ffffffffyyxx0001 -> new style sprite mode word
wttttvvvvvvvvvvvvvhhhhhhhhhhhhh1 -> RISC OS 3.5-style sprite mode word

• s = shadow mode bit
• m = BBC – RISC OS 3.1 mode number
• p = pointer
• w = wide mask flag
• t = sprite type (only types 0-15 available in old style sprite mode word):

• f = duplicate of bits 8-15 of ModeFlags
• x,y = compact resolution specifier:

• h,v = horizontal/vertical dpi: allowed values are 180, 90, 45, 23 and 22

As always, when creating sprites, you should always use the most backward-compatible respresentation representation possible. If your sprite can be expressed as a mode number then do so, else if aRISC OS 3.5 sprite mode word can be used then do so, and only if both of these fail should you use a new sprite mode word.

Mode strings

These are used in *WimpMode. Note that BASIC’s MODE <string> merely calls *WimpMode. A new BASIC syntax, MODE OF <string> is proposed to set the mode without affecting the WimpMode – to facilitate this, implement OS_ScreenMode 15 (such that it is compatible with RISC OS Select).

The following new variants of the colour parameter are required:

• “C4K” / “C4T”: 16bpp 4:4:4:4
• “C64K” / “C64T”: 16bpp 5:6:5
• “G16M”: 24bpp 8:8:8 packed – note C16M is already taken, and there’s precedent for a “G” prefix indicating an alternate version of a mode

The user may wish to select between different variants of 16, 24 or 32bpp modes. For example on OMAP-based designs, selecting alpha rather than transparency will enable blending with the video plane, or switching the red and blue components will enable use of the TV output. However, both of these come at the cost of application compatibility, which is why I think they should be a user option.

It is proposed that the available options be controlled by the new “L” parameter, and distinguished by listing the colour components in big-endian order, leading to the following possible parameters:

• “LTBGR”: the default, unless not supported by the hardware
• “LTRGB”
• “LABGR”
• “LARGB”

For example, to set up a TV output on an OMAP design, you could use:

*WimpMode</notextile> X720 Y576 C16M LTRGB

I can’t see any need to support CMYK or YCbCr formats for Wimp use.

BASIC parameterised MODE statement

The multi-parameter MODE statement in BASIC is a front to SWI OS_ScreenMode 0, not to *WimpMode. Since the majority of the time when you use MODE you’re running a full-screen application rather than reconfiguring the desktop, this is the call you’ll want to use (unless you’re happy with a RISC OS 3.1-compatible mode number).

BASIC’s HELP is famously terse. The <bpp> parameter is currently interpreted as

It is difficult to elegantly extend this syntax, beyond perhaps adding 12 and 24bpp options.

Bearing in mind the new MODE OF <string> syntax proposed above, extension may not be required.

HAL interface

To be defined